High-power power supplies |

These are compact high density, high power supplies and power supply sub-assemblies, made for integration into your technically advanced product. One of the most difficult parts of a power supply over 1kW is to design a reliable PFC front-end (Power Factor Correction). We have proven board sets with demonstrated MTBF of 500,000 to > 1 million hours. Let our designers assist you with the integration of our high performance isolated or non-isolated PFC bulk converters into your design. We can accommodate special input power cycling requirements and unusual dynamic load profiles.

We can provide your system with a low voltage bus (12 to 56VDC) for RF power modules, battery charging, telecom back planes, house keeping or high voltage bus (100 to 400VDC) for motor controllers, UPS battery charging, or the bus voltage before the high voltage step-up circuit to power RF or X-ray tubes.

Other features include: paralleling supplies to 10’s of kilowatts of output, hot plug modules, N+1 redundancy, full universal input range, low ripple & noise, wide operating temperature range, and standard compact case sizes of 5 x 3RU, 5 x 2RU and 5 x 1 RU. Supplies and board sets are designed to meet all international safety & EMI standards.

Data sheet for single outputs

• Wide input 90 TO 264VAC 500 to 1500w – Single phaseStandard input
• 170 TO 264VAC 1000 to 3000 – Single phase

1.2 to 12VDC single output supplies – non programmable

• 500 to 1500 watts, input range 85 to 264 Vac
• 1000 to 3000 watts, input range 170 TO 264 Vac
• 1.2 to 12VDC single output supplies – Programmable

Our Non-Isolated Front End Bulk provides up to 10,000W of Power Factor Corrected Bulk Power for Pulse Width Modulated DC-to-DC Converters and Distributed Bus DC Systems.

In addition to 30% reduction in RMS line current, these bulk power units have improved hold-up performance, reduced line harmonics and insensitivity to voltage and frequency variations

Features include:  Power Factor (>0.99), operating temperature 0°C to +50°C at full load, compact case, input and output fuses, Designed to meet IEC 555-2 for Line current harmonics, meets UL, CSA, TUV, EMI EN55022 level A and certified to CE. Converter has over-voltage protection, over current protection, over temperature protection and under voltage detect

Available options include Intelligent Controller, Maximum Power Point Tracking and Battery Management features; Float Voltage, Recharge, Temperature Compensation, Low Voltage Disconnect, High Voltage Disconnect, Equalize. Other options: DC Input OK, DC Output OK, Remote Enable/Disable, Programmable Input & Output Monitor, Output Voltage & Current, Monitor Input Voltage & Current

Data sheet PFC Non-Isolated Bulk supplies.

• 1100 to 5000 watts, input range 85 to 264VAC – Single phase
• 2250 to 10,000 watts, input range 170 to 264VAC  – Single phase
• 2250 to 10,000 watts, input range 170 to 264VAC  – Three phase
• 2250 to 10,000 watts, input range 365 to 528VAC  – Three phase

Our PFC isolated front ends provide 24, 26, 28, 32, 48 or 54VDC in a single output. These are complete front-end solutions for driving high-density DC-to-DC modules in distributed power systems with N+1 redundancy.

This series offers a variety of output voltage ranges. Mid-voltage output is from 15 to 60VDC, & high-voltage output is from 70 to 300VDC. Both products offer output power from 1kW to 10kW (no hold up time) and AC input from 90 to 264 single or three phase or 365 to 528VAC three phase.

Features include:  Power Factor (>0.99), operating temperature 0°C to +50°C at full load, compact case 5” x 3RU x depth of 11.25" (10kW depth 17”), over temperature protection, meets UL, CSA, TUV, EMI EN55022 level A and certified to CE. Output is fully floating, has over-current protection, over-voltage protection and remote sense.

Meeting international safety and EMI standards, this IFE series provides highly reliable and rugged compact power with DMTBF over 500,000 hours. Wide temperature de-rated models operating over -30°C to +70°C are also available.

Typical Options include: Hot Pluggable, Wide Temperature Operation, Power Fail Signal, Logic Inhibit, Marginning / Programming, Power Good Signal, Single Wire Current Sharing, Wireless Droop Current Sharing, Output Current Monitor, or Isolation Diodes.

Data sheets PFC Isolated Front End

• 15 to 60VDC, non-programmable.
• 1000 to 8,100 watts, standard temperature range
• 864 to 3600 watts, wide temperature range
• 70 to 300VDC, non-programmable.
• 15 to 60VDC, programmable.
• 70 to 300VDC, programmable.

Our flexible power shelves are built to industry standard 3U height. The 19" shelf is 3-positions wide and the 24" shelf 4-positions wide.

These shelf systems provide a complete solution, and are ideal for distributed power system, communications and data processing applications requiring N+1 redundancy.

These are designed with Elcon Top and Lower Drawer hot plug connectors to provide you with full capabilities and flexibility required to maximize system integration. Rack systems also permit logical expansion, as future upgrades place additional demands on the system power requirements.

A 23" four-position 3U shelf is designed to provide 20KW of system power and 15KW of redundant power using four 5KW supplies. Multiple shelves can be combined in a rack to provide 100kW of DC power. In the case of our 8100W supply 24,300 watts can ft into a 3U 19" power shelf.

Shelf rack I/O interfaces such as terminal blocks, bus bars and flying leads to the system. The flexible racks can also be tailored to specific needs offering performance, reliability and innovation to provide a complete power solution. In addition these are integrated with features such as single wire current sharing, wireless droop current sharing, isolation diodes, alarms and LEDs, and true hot plug power supplies offer a glitch-free fault tolerant system.

Data sheets - 3U Standard Power Shelves

• 19”, 3 Position – 9kW Max Power
• 19”, 3 Position – 24.3kW Max Power
• 23”, 4 Position – 12kW Max Power
• 23”, 4 Position – 32.4kW Max Power